We do not recommend to fog for termites in an attic. It will not penetrate the raw wood. In this case we recommend to treat using Boracare. Boracare will penetrate up to 4 inches into the wood and will last the lifetime of the wood. You can paint it, spray it, or foam it onto the raw wood.
Bora-Care is a very safe product and it is considered a green product as well. Typically, it takes about an hour for the surface of the wood to dry. After application has dried completely, it should be perfectly fine for children and pets to re-enter the house. Please read the BoraCare product label for complete usage instructions. Boracare does have to be applied to raw, untreated, unpainted wood.
As long as the top is sealed then you can safely apply Boracare to the underside if unsealed and it will penetrate through the wood. It would be recommended to allow the butcher block to dry for 24-48 hours before using again. Any food contact surfaces treated with Boracare must have a sealant applied after the Boracare has dried.
No, Boracare should only be mixed with water and applied to raw wood.
Any untreated or unstained wood, including plywood, would benefit from an application of Boracare to help protect it from wood infesting pests, fungi and dry rot. If you do have an active infestation of pests in the wood Boracare would be the best treatment for that as well before you stain. When treating wood that may be exposed to rainfall, be sure to apply a water sealant after the Boracare application has dried.
Boracare should only be applied directly to wood. We would recommend using something like Termidor Foam in the wall voids. This product will be injected at the studs of the wall. Termidor Foam is a non-repellent so the termites do not know they are coming in contact with it. You can drill holes in the stud every 10-12 inches apart. This product has a residual of 3 months.
Boracare cannot be used to treat fruit or any other types of trees, as it would kill any type of plant life. If you can give us more information about what kind of pest you need to treat, we will be happy to recommend a different product for your needs.
For furniture your options are limited for treatment. If the wood is in its all natural raw state without any stains or finishes on it you can use a product like Boracare. Boracare will absorb all the way into the wood and eliminate any infestation that is there and last for the life of the wood. It does not stain the wood or leave behind any visible residue, but becomes one with the wood and any insect that ingests it dies. If the furniture has a finish on it, you would either have to drill holes throughout it and inject something like the Boracare or a foam, or the option most go with, hire a company to fumigate it
Bora-Care should only be applied to raw wood in its natural form only for proper penetration. If there is a laminated coating on the beam the product will not be absorbed properly.
When using Boracare for an exisiting infestion you woud want to use it at a 1:1 mixing ratio.According to the Log Home and Dimensional Lumber tech Bulletin on this product you would get 75 linear foot of coverage per gallon once it is diluted.
Bora-Care will not stain concrete or flagstone. The effects you are speaking of should be temporary.
Unless a dye was added to the Bora-Care at the time of application, you would not be able to tell if the wood in your crawlspace has been treated or not.
Bora-Care can be used on raw, untreated wood surfaces indoors and is safe for kids and pets once dry.
Regular Bora-Care does not treat or prevent mold in the wood, only wood decay fungus and wood-destroying insects. For mold remediation or prevention, you should use Boracare with MoldCare. This product needs to be applied directly to the wood to be absorbed, so if the insulation is blocking the wood, then you do need to remove it before spraying. Boracare with MoldCare does not remove stains, so if you want to remove any stains or other discoloration, you can treat the wood first with Mold Clean.
Wood treated with Bora-Care will appear darker than normal for a few days until the chemical dries. Typically it only takes 24 - 48 hours for the product to dry and not be sticky. If it is not drying within this time frame, it usually means that too much of the product was applied to the wood. You could lightly sand the wood to remove the stickiness and then apply your finishing oil.
If you know that you have termites or carpenter ants in treated wood, then we would recommend spot treating with a non-repellent insecticide that will transfer throughout the colony, such as Fuse Foam. Fuse Foam is a ready-to-use product that has a foaming agent to help it expand and fill galleries. You would need to use the kickout holes as a guide to drill into the termite/ant gallery so that you can get at least some of the product in direct contact with the live insects. The product then works slowly enough to get transferred throughout the whole insect colony and cause collapse. If you prefer a Borate product, then we recommend the ready-to-use formulation of Boracare called Jecta. Jecta is designed for spot treatments.
Boracare should not be applied to food contact surfaces. If there were overspray on sinks, countertops, floors, etc., then you could wipe up the excess with a disposable cloth and then clean the area with warm, soapy water. To prevent contamination in the future, it is recommended to cover non-target surfaces with a tarp or drop cloth before applying Boracare indoors.
Bora-Care is too thick of a liquid to be used in any type of fogger. It can be foamed into wall voids, or sprayed or painted directly onto raw, untreated wood only. If you cannot directly access the wood that needs to be treated, foaming with Bora-Care normally is the best solution, although it will only penetrate into wood that it is directly contacting.
Yes, you can apply Bora-Care to the plywood in this area as long as the plywood has not been treated with anything else.