Dominion 2L Termiticide - Questions & Answers

Displaying 1 to 10 (of 126 questions)
  • Asked by David from Atlanta, Ga
    07/07/2015
    Q
    How would I perform a soil drench treatment in my house is on a slope?
    I would like to buy Dominion Termiticide to apply as a barrier around the house and set and forget (for 7 years at least). Several sides of my house has steep declining slopes against the house. What is the best method of trenching and applying to account for the slopes. I'm afraid that trenching 10ft then pouring the diluted mixture will run off. Thank you.
    A

    You can do the soil drench treatment by digging a 6x6 inch trench around the foundation and pour 2.4 fl oz of Dominion 2L into 4 gallons of water per 10 feet. With the sides of the house with the slope make sure you are doing a backfill method. With the backfill method you want to treat the soil that was removed when digging the trench before placing it back into the trench. If you need any more information about our performing a soil drench treatment you can look on our Termite Treatment guide 

    Was this answer helpful to you?   Yes No
    1 of 4 people found this answer helpful.
  • Asked by George from North East, Ohio
    06/03/2021
    Q
    What about limits on trench and drench around foundation using Dominion 2L?
    Around my house there are a few areas that are challenging to trench around 6 inches wide and deep along the perimeter. When using Dominion 2L, what are the concerns if there was no trench, but the 4 gallons per 10 feet were poured along the base slowly enough to allow soaking along the base with minimal runoff from the base of the foundation?
    A

    Simply pouring a termiticide such as Dominion 2L around the foundation will not provide ample protection from termites. There is no guarantee how deep the product will absorb into the ground, and you need a termiticide at least 6 inches deep for termite protection. Another option would be to create holes using a rod or dowel that is at least 6-12 inches deep every 12 - 18 inches, then you would still be appling 4 gallons of solution per 10 feet by pouring the product evenly into each hole.

    Otherwise, bait stations such as the Advance Termite Bait Stations are placed 2-4 feet out from the structure, outside the dripline of the roof.

    Was this answer helpful to you?   Yes No
  • Asked by L. from Billings, Montana
    05/22/2013
    Q
    How to use Dominion 2L for engraver beetle and pine bark beetle?
    Direct trunk spray vs. drench?
    A
    To treat for pine bark beetle, you can do either. When using Dominion 2L as a soil drench for pine bark beetles you should use 0.2 fl. oz. (3 to 6 mL) of Dominion 2L per inch of trunk diameter (D.B.H.) diluted in 1 pint - 1 gallon of water per inch of trunk diameter.    The amount of water that is used will vary depending on soil conditions and volumes that are easy for applicators to use. The minimum amount of water that should be used is 1 pint per inch of trunk diameter but you may use 1 quart -1 gallon of water per inch of trunk diameter. Denser soils such as clay do not accept water as readily, so the lower volume of water is suggested.  Since sandy soils can accept more water, using the higher volume of water is preferred. After the soil drench has been applied you should water it in with at east 1/2 inch of water. Note: Water simply acts as a carrier and it is important that even distribution of the product is achieved. Thus, more water may be used if the applicator feels runoff will not occur and proper penetration of the root zone is achieved. Insecticides applied to the soil are taken up by the roots and trans-located throughout the tree or shrub. Root/soil drenches offer the advantage of requiring no special equipment to apply (other than a bucket or watering can). However, surface layers of organic matter, such as mulch or leaf litter, can bind the insecticide and reduce uptake. Before applying drenches, it is important to remove or pull back any mulch or dead leaves so the insecticide solution is poured directly on the mineral soil. It is also important to keep the soil around the tree or shrub moist for the next 7-10 days after applications to encourage uptake.
    Was this answer helpful to you?   Yes No
    14 of 14 people found this answer helpful.
  • Asked by Trisha from Dequincy, Louisiana
    11/05/2013
    Q
    I purchased termidor for a trench around our house. And dominion as agree drench. Will close proximity work?
    We just built a house on piers. We purchased termidor for the house. Do we trench around the perimeter an also each of the 52 piers? We also purchased a bunch of rough cut lumber for a barn. We noticed each piece that touched the ground was eaten up and infested with termites. I sprayed demon wp and killed the visible termites but I know there are more. Can I use either of these products And spray directly on termites I see under wood around our 5 acres? Last question, we have several trees on the property. I have seen active termites at the base of each tree. I'm not sure if they are in the trees but all of the trees look sickly. What product should I use and how do I apply it to the trees?
    A

    If you know where the termites are active we do recommend directly treating that area with Dominion 2L. You should trench and treat around the exterior walls, inside crawl spaces, and trench and treat around each pier for best results. Any part of the home that touches the soil should be treated around.

    Termites do not normally attack live, healthy trees so you most likely will not find any products that will work as a ground barrier around the trees.  Most people are primarily concerned with protecting the big investment, their home, and Termidor would be the best product to use for that, as it last 10 years in the soil, whereas Dominion will only last 5-7 years.  It is only labeled to be used adjacent to the structure though.
    Was this answer helpful to you?   Yes No
    2 of 2 people found this answer helpful.
  • Asked by Kim from Lincoln, Ne
    05/16/2019
    Q
    We have an earth berm home, so the roof on the north side is so low I can't get under to trench
    The roof is only a couple feet off the ground, so I can't get under it to dig a trench to pour the termiticide. If I repeat the treatment every year, can I just use it as a soil drench, like I would if I were treating a tree for bugs? I could do that, and maybe scrape a bit of a shallow trench under there to pour into.
    A

    If you cannot trench with Dominion 2L Termiticide Concentrate in an area you would just have to leave that area open as a possible entry or you can use stations in the area as part of prevention.  Applying Dominion as you would a soil drench to a plant would not have the same effect as it would in an actual 6 x 6 trench.  It lasts 5-7 years in the soil so would not be applied once a year for termite prevention.

    Was this answer helpful to you?   Yes No
  • Asked by Patty from Hedgesville, Wv
    08/09/2011
    Q
    Will Dominion 2L work to kill hemlock wooly adelgids?
    2 trees badly infected. Big trees so I have to do the soil drench method.
    A
    Dominion 2L is labeled for adelgids and will be able to help with hemlock wooly adelgid infestations. Because hemlocks are shallow rooted, a soil drench with Dominion can be effective. Whatever method is being used to make a soil drench, whether using power equipment, a bucket or watering can, it is important to make sure the application is evenly distributed and does not run off. Soil treatments should be made when the soil is moist. Fall to early winter and spring to early summer are recommended periods for making soil applications for the HWA. It can take 2-3 months for imidacloprid products to be translocated through trees that are about 15 inches in diameter. This process may be faster or slower, depending upon the size and health of the hemlock and other environmental conditions during and after the application.  It is advisable to make soil applications of imidacloprid products to hemlocks before they become heavily infested and stressed by the HWA— to ensure good translocation through the tree.
    Was this answer helpful to you?   Yes No
    14 of 14 people found this answer helpful.
  • Asked by Bill from New Jersey
    10/12/2014
    Q
    French Drain
    3 yrs ago, we had a french drain and sump pump installed in or Basement.The following 2 springs, we had a termite swarm in the basement. I am going to treat the outside perimeter with Dominion 2 but feel that they are under basement floor. Can I pour Dominion in the french drain
    A
    In order to answer you question accurately we need some more information. Please contact one of our Customer Service Reps Mon-Fri 9am-5pm EST at 1-866-581-7378 and we are happy to assist you.
    Was this answer helpful to you?   Yes No
    0 of 1 people found this answer helpful.
  • Asked by Mike from Bryan, Texas
    07/27/2013
    Q
    Where to apply Dominion 2L as a drench?
    I plan to use Dominion 2L on my post oak trees to control tree boars. I have read the label that came with it and I think I understand the mixture rates. However, I do not know where exactly to place the drench. Do I drench at the drip line, at the base of the trunk or somewhere in between? Also, can Dominion 2L be injected directly into an infested tree - if so how and where? One of my oaks is infested and I wondered if direct injection may give it a better chance? Thanks
    A
    You can apply Dominion 2L as a drench any where between the base and drip line of the tree. You want to make sure that  you keep the soil moist for up to 7 days after applicaiton to ensure the product will be more quickly soaked into the root system. We do not recommend Injecting Dominion into the live tree. Please follow the product label for instructions.
    Was this answer helpful to you?   Yes No
    7 of 7 people found this answer helpful.
  • Asked by Cecilia from Howell, Nj
    06/30/2013
    Q
    How do i use Dominion for indoor potting soil drench?
    I have been using Bonide house plant granules (0.22% imidacloprid) in the soil of 2 large jade trees and other smaller pots in my sunroom to combat mealy bugs systemically. The Bonide label specifies how much product to use based on the diameter of each pot. Now that summer is here I can take the plants outside to spray them. As a foliar spray specifically for houseplants, the Dominion 2L label recommends 45ml/100gal which works out to be about 2.5ml or ½ teaspoon per gallon. That’s easy enough as a foliar spray but I want to drench the soil in each pot so the plants can continue to take up the imidacloprid through their roots. Since I have Dominion 2L, I’d prefer to use a liquid solution instead of using the Bonide granules in each pot. Question: Given that the label states Dominion 2L can be used as a foliar spray for indoor plants, do you see any problem with using it in the potting soil of indoor plants as well (like the Bonide granules)? The Dominion 2L label recommends a soil drench of 3ml-6ml per inch of tree trunk diameter mixed with enough water to deliver that amount of imidacloprid evenly. The label is referring to outdoor use but I’m wondering if that translates to indoor trees as well. For example, my indoor jade trees have trunks with 6” circumferences (1.91” diameters). To me, that means each jade tree that size would need 6ml-11ml of imidacloprid in their potting soil. I’d probably use 1½ teaspoons (7½ ml) Dominion 2L in a gallon of water for each jade. Question: Do you agree? But, what solution would I use for my smaller potted plans that don’t necessarily have trunks to measure? I don’t see anything on the label about a potting soil drench for indoor plants; the soil drench solutions for outdoor perimeter use (termites, ants etc.) are way too potent I believe. Question: Do you think it would be effective to use the foliar spray solution (1/2 teaspoon/gallon) on the leaves and then drench the soil with the same? I’m not convinced of this idea. It seems that the amount of water the product is delivered in is not as important as the specific amount of imidacloprid delivered per size of plant (or pot). Thanks for your help when you have time.
    A
    You are pretty much spot on, on most of your calculations. There shouldnt be any problem using the Dominion 2L in the soil of the potted plants in a drench method. The amount you calculated for the jade tree is correct for the drenching of its roots. For plants that do not have a trunk circumferance large enough to really matter, treat the plant as a shrub and go by heighth to determine the correct amount of solution to use per foot of shrub height. The .6 ounces is foliar dilution only so it wouldnt be the best option to just use automatically if the plant is smaller and calls for less. Also, you are absolutely CORRECT in that the water acts as the carrier of the product so making sure the amount per plant is right is the biggest key. Please let us know if you have any other questions!
    Was this answer helpful to you?   Yes No
    9 of 11 people found this answer helpful.
  • Asked by A. from Coral Springs Florida
    12/06/2013
    Q
    How do you use Dominion 2L as a soil drench?
    I have several trees with different tree trunk diameters. I like to know how best to mix Dominion with water for each tree application. Example, one tree is 5 inches in diameter and an other 102 inches in diameter 1. what is the mix rate of Dominion and water per tree? 2. do you apply with a watering can for an even distribution? 3. Where do you apply, at the base of the tree or at the line of foliage? 4. What t matter if there is grass or other plants in the area? 5.Do I have to moist the ground before application and maintain moist thereafter?
    A
    You will need 0.1 to 0.2 fl oz of Dominion 2L per inch of trunk diameter for trees at the base of the tree inside in the drip line. The amount of water that is used will vary depending on soil conditions and volumes that are easy for applicators to use. The minimum amount of water that should be used is 1 pint per inch of trunk diameter for trees but you may use 1 quart -1 gallon of water per foot of height (or inch of trunk diameter for trees) as well. Denser soils such as clay do not accept water as readily, so the lower volume of water is suggested.  Since sandy soils can accept more water, using the higher volume of water is preferred. After the soil drench has been applied you should water it in with at east 1/2 inch of water. Note: Water simply acts as a carrier and it is important that even distribution of the product is achieved. Thus, more water may be used if the applicator feels runoff will not occur and proper penetration of the root zone is achieved. Insecticides applied to the soil are taken up by the roots and translocated throughout the tree or shrub. Root/soil drenches offer the advantage of requiring no special equipment to apply (other than a bucket or watering can). However, surface layers of organic matter, such as mulch or leaf litter, can bind the insecticide and reduce uptake. Before applying drenches, it is important to remove or pull back any mulch or dead leaves so the insecticide solution is poured directly on the mineral soil. It is also important to keep the soil around the tree or shrub moist for the next 7-10 days after applications to encourage uptake. - See more at: http://www.domyownpestcontrol.com/dominion-2l-termiticide-concentrate-p-1223.html?keywords=drench&search_for=questions#questions
    Was this answer helpful to you?   Yes No
    33 of 36 people found this answer helpful.
Displaying 1 to 10 (of 126 questions)