Hi-Yield Triclopyr Ester has a shelf life of 3-5 years, if stored in a cool, dry place.
It is best to apply herbicides like Hi-Yield Triclopyr Ester with a hand pump or backpack sprayer, rather than with a hose-end sprayer to ensure the most accurate application. You will use 3/8 - 3/4 oz. (2.25-4.5 teaspoons) per gallon of water per 1,000 sq. ft. For specific application instructions, please refer to the product label.
It can take about two weeks to start to see results after applying Hi-Yield Triclopyr Ester. You may need to make a second application after four weeks depending on what weeds you are treating. Please refer to the product label for complete application instructions.
The product label Hi-Yield Turflon Ester Ultra does not recommended using a surfactant so it would not be needed.
According to the Hi-Yield Triclopyr Ester product label, it is a herbicide used to control unwanted annual and perennial broadleaf weeds on perennial bluegrass, perennial ryegrass, and tall fescue ornamental turf (including sod farms, commercial turf, and golf courses). The label also states Hi-Yield Triclopyr Ester may injure certain turfgrass species. Do not apply to Bahiagrass, Bentgrass, Bermudagrass, Centipedegrass, St. Augustine grass, or Zoysiagrass, unless turf injury can be tolerated.
Hi Yield Triclopyr Ester works best when its used on plants that are actively growing and when soil temps are 50 degrees or higher at the time of the application. You would ideally want to apply it between 50 and 80 degrees. Be sure if you are spraying over lawns that you are spraying it on a tolerant turf species.
Yes. Hi-Yield Triclopyr Ester is labeled for ground ivy (also known as creeping charlie) and can safely be applied to perennial cool season grasses, bluegrass, ryegrass, or tall fescue. Please check the product label to be sure your turf is tolerable.
Hi-Yield Triclopyr Ester is best applied when the plants and ground are dry. The moisture will lessen the effectiveness of the product.
After an application of Hi-Yield Triclopyr Ester you should wait 24 hours before watering your lawn.
After an application of Hi-Yield Triclopyr Ester you should wait 24 hours before watering your lawn.
Hi-Yield Triclopyr Ester Ultra is applied at 3/8 - 3/4 oz. (2.25-4.5 teaspoons) per gallon of water per 1,000 sq. ft. (8 - 16 oz. per acre). See label for complete application instructions. It is recommended to add a non-ionic surfactant for best results when treating brush, vines, small trees, and some other weeds. Do not use a surfactant when treating a lawn because this could cause the lawn to be damaged or burned.
Hi-Yield Turflon Ester Ultra states on the product label: Do not reseed for 3 weeks after application.
Hi-Yield Turflon Ester Ultra is a selective post-emergent herbicide that will be most effective on young, actively growing weeds listed on the product label. It will be difficult to get control using post-emergent herbicides once temperatures are consistently less than 60 degrees and plants are beginning to go dormant.
Hi-Yield Triclopyr Ester has 61.6% triclopyr, and Alligare Triclopyr 3 contains 44.4% triclopyr, so these products will have different dilution rates. How much product you use and which one is appropriate for your needs will depend on the application. Triclopyr 3 is more for industrial applications like rights-of-way, whereas the Hi-Yield Triclopyr Ester is more for residential areas or smaller applications.
There is no difference between active ingredients contained in Hi-Yield Triclopyr Ester or Remedy Ultra Herbicide. The only differences between the two products is the manufacturer and the size of the bottle that can be purchased.
You will use 1 tbsp. of Hi-Yield Turflon Ester per 1 gal. of water to treat 1,000 sq. ft.
Yes, you can mix Triclopyr Ester with Tenacity herbicide to achieve better control of tough weeds such as Bermudagrass and clover. We recommend that you review the Tenacity Supplemental Label here that addresses rates for these products when mixing.
Yes, Hi-Yield Triclopyr Ester and Monterey Turflon Ester Herbicide both have Triclopyr, butoxyethyl ester 60.45% as the active ingredient. They are just made by different manufacturers. Both products are labeled for Oxalis. Please be sure you check the product label for your turf type and proper mixing instructions.
It is recommended that after treating with Hi-Yield Triclopyr Ester, you will need to wait until the application is completely dry, usually 2-4 hours, before letting the dog back into the treated areas. There is very little product actually being applied and the small amount that could be ingested should not be harmful to most pets.
We want to be clear that Bermuda can be suppressed using Hi-Yield Triclopyr Ester, but it is VERY difficult to kill completely. It will take multiple treatments to finally control it. Per the product label, apply Hi-Yield Triclopyr Ester at the rate of 3/4 fluid ounces per 1,000 square feet. Three to four additional applications at 4-week intervals will be required to give adequate suppression of bermudagrass and allow fescue or other desired turfgrass species to dominate.