Before applying any chemicals, it is crucial to prepare the area for treatment by removing clutter, vacuuming, steaming (optional), and encasing mattresses and box springs. Taking time for these preparation steps will make your treatments much more successful. Using the products in your Bed Bug Kit, treat all cracks, crevices, voids, tufts, seams, and folds where bed bugs may be found. Always keep pets, children, and other people out of the treatment area until the products have dried - usually about an hour.

STEP 1 - SPRAY - PT Alpine Flea and Bed Bug Aerosol

*PT Alpine Flea and Bed Bug Aerosol is a ready-to-use product that provides quick knockdown of bed bugs.

*PT Alpine Flea and Bed Bug Aerosol can be applied at any angle, making treatment of remote areas easier.

*Apply PT Alpine Flea and Bed Bug Aerosol as a spot or crack and crevice treatment to the following areas where evidence of bed bugs is found, contacting as many bugs and eggs directly as possible:

• Around bed and furniture legs - Inspect wheels, casters, posts, and legs of all furniture.
• Behind wall fixtures
• Under floor lamps
• Cracks and crevices along baseboards and floor moldings
• Beneath floor coverings and along the edges of wall-to-wall carpeting
• On infested mattress and box springs - Remove linens, then apply to tufts, seams, folds and edges. Do not treat entire surface area of mattresses.
• Cracks and joints in bed frames, headboards, dressers, shelves, and other furniture
• Picture frames and wall coverings - Remove from the wall and treat cracks and crevices on and behind these items.
• Around door frames, window frames, and thresholds
• Upholstered furniture - Apply only to the infested tufts, seams, folds, and edges, but do not apply to flat surfaces where prolonged human contact will occur.

*Do not remake beds or replace items on shelves or in drawers until spray has dried.

*Shake Well Before Use

STEP 2 - DUST - Bellow Hand Duster and CimeXa Insecticide Dust

*Once your spray application has dried, you can apply the insecticide dust.

*Using insecticide dust can be very messy, so be sure to wear gloves and consider having a moist paper towel handy to clean up excess dust.

*To fill the Bellow Hand Duster, remove the black rubber stopper on top of the duster. Gently unscrew the white top of the CimeXa dust, then slowly tap the dust into the duster. Fill the duster up to halfway (or less), so there is plenty of room for the dust to move inside the duster.

*You may want to add a few small objects such as coins, pebbles, or marbles to prevent clumping inside the duster.

*Replace the black stopper so that it fits snugly into the opening. Remove the black rubber cap from the end of the extension wand. To apply dust, hold the duster upside down, so that the extension wand is on top, then gently squeeze the bellows between the thumb and fingers.

*Apply CimeXa Dust to voids and other hidden areas where it will not be disturbed, such as:

• Behind electrical faceplates - Remove switch and electrical plates to gain access to wall voids.
• Along baseboards - Treat any cracks in, above, or below baseboards where the tip of the duster will fit. Also treat under the edges of carpeting where you are able.
• Headboards - Remove from the wall or dismantle to allow thorough treatment.
• Drawers and furniture - Remove drawers and treat along tracks and support, as well as the corners and edges of the cabinet. Also treat in cracks and crevices on the undersides of cabinets and other furniture, and in any hollow areas such as bed frame tubing.
• Box Springs and upholstered furniture - Check for tears in fabric backing or other hollow areas where the tip of the duster may fit, and treat these areas.
• Behind wall fixtures - Remove fixtures from walls and treat behind each one.

*Be careful to avoid over-dusting. CimeXa Dust is very fine, and it only takes an extremely small amount to kill a bed bug.

*If dust escapes into open areas, simply wipe up the excess dust with a moist paper towel.

*Do not apply dust as a broadcast or in open areas where it will be moved around as it can become an irritant.

STEP 3 - CONTACT KILL - Sterifab

*Sterifab does not require dilution, but you should shake the container well before spraying.

*Sterifab will kill bed bugs and other insects on contact only, so it is only active when it is wet.

*Because of this short action, you can apply Sterifab almost anywhere bed bugs are found.

*Use Sterifab in areas where you see live bed bugs, especially where you cannot use residual products, such as:

• On the resting areas of sofas, chairs, mattresses, or other upholstered furniture
• Open areas on carpets or floors where live bugs are seen
• Walls, baseboards, or corners

*Sterifab will stay active as an insecticide, virucide, fungicide, bactericide, mildewcide, germicide, etc. as long as it is wet. Sterifab leaves no residual after it has dried.

*Do not apply to clothing items or directly to people or animals.

*Use as needed to spot treat live insects.

STEP 4 - TREAT CLOTHING AND LINENS

*Although this step does not NOT involve any chemicals in your kit, it is a crucial part of your treatment.

*Clothing, linens, or other fabric items in the infested rooms should be removed in bags, then washed and dried or dry cleaned.

*Do not return items to the infested areas until there has been no evidence of bed bugs for 30 days.

*Failure to make sure all items being returned to the room are bedbug free may cause a reinfestation.

STEP 5 - REPEAT! REPEAT! REPEAT!

*Repeat Step 1 (PT Alpine Flea and Bed Bug Aerosol) every 7-10 days days until no one is getting bitten and there is no further evidence such as live bugs, cast skins or fresh blood spots found. This is absolutely crucial! Depending on the severity of the infestation it can take a minimum of 7-8 weeks, including repeat treatments. Failure to be thorough can prolong the bed bug control process and can make it harder to eliminate them.

*Use Sterifab as frequently as needed to kill live bugs on contact.