Talstar P would be a great choice for indoor and outdoor tick control. We also recommend adding an insect growth regulator such as Archer IGR to Talstar to stop the ticks from being able to mature while you are trying to eliminate the infestation. You will use 1 oz of Talstar + 1oz of Archer IGR per gallon of water per 1,000 sq ft area. Do not make spot applications. Treat the entire area where exposure to ticks may occur. Use more water (not more product) when treating areas with dense ground cover or heavy leaf litter. Ticks may be reintroduced from surrounding areas on host animals. Retreatment may be necessary to achieve and/or maintain control during periods of high pest pressure. All of your pets should be treated with a product that is specifically labeled for use on pets for tick control.
You can also help by creating a "tick safe zone" in your yard. You should have an area that is at least 9 ft wide between your yard and any wooded area. Trim back trees to allow as much sunlight as possible into your yard. Keep grass as short. Remove as much leaf litter as possible. A clearly defined, well manicured border between your yard and any wooded areas or weedy lots will reduce the chance of ticks infesting your yard.
You can use a hose-end sprayer to apply Talstar P. You shoul use 1 oz per 1000 sq ft, and we recommend using 1-3 gallons of water per 1,000 sq ft. Keep in mind that it is most important to use the correct amount of concentrate and then think of the water as a carrier, so it is better to use a bit more water than to use too little. For example, to treat half your yard, you would use 7.5 oz at a rate no higher than 1 oz per gal of water, but usually it is best to use a rate of 0.3 or 0.5 oz per gal of water with a hose-end sprayer. You can always start with a small area and test using just water to get an idea for how heavily you tend to spray and how fast you walk when spraying.
Yes, you can use Talstar P in both food/feed and non-food/feed areas of food-handling establishments like restaurants as a spot or crack and crevice spray. Be sure this is not while the restaurant is in operation, and that you are not contaminating food, utensils, or food-handling surfaces. Please see Page 6 of the product label for complete directions on using Talsar in Food/Feed Establishments.
Talstar P (Talstar One) is a great product to use for fungus gnat control. It is to be used inside and outside the home, but will only kill the adults as the larvae is protected in its egg form much like a chicken egg is protected until cracked. To control the larvae you would need to mix the NyGuard IGR (birth control) in with the Talstar. NyGuard is labeled for fungus gnats as well as a large variety of other insects to sterilize the adults from being able to lay viable larvae. This will control the population drastically in keeping new ones from developing. You should mix 1 ounce of Talstar P with 4 ml of NyGuard IGR to each gallon of water you use. Talstar P can be used as a broadcast over the entire lawn or just as a perimeter treatment. You will want to focus on the mulch bed area and the underside of shrubs, bushes, or trees in the area. It is completely safe to spray on ornamentals. In the garage area, spray as crack and crevice and focus on damp areas/reducing the water/moisture. Please let us know if you have any further questions.
Talstar is a great option for mosquito control and can be used in either a mist blower or a sprayer.
For outdoor use the Talstar P will be safe for animals of all kinds once dry. For indoor use if you have pet birds, we recommend removing the birds from the home while you treat and for at least 4-6 hours to give plenty of time for the product to dry and air out. Birds are more sensitive to chemicals and smells so keeping them out of the treatment areas for longer than pets like dogs and cats is recommended. If you have any safety concerns regarding its use around your birds please take info on the product to your birds vet for consultation.
When using Talstar P, the mixing ratio is 1 fl. oz. per gallon of water. This will generally treat 1000 sq. ft. For your lawn, you will need to fill up your sprayer at least three times to complete your entire lawn. The pint size of Talstar P would make 16 gallons of solution and treat 16,000 sq ft.
Both non-repellents and repellent insecticides will eventually eradicate the pests that the products are labeled for. Non-repellents allow more time for the insects to be able to take the product back to their colony and transfer the product among each other. "Repellent" insecticides, such as Talstar P, are not detected until the insect you're treating comes in contact with the product - it will give off a "tingling" sansation or so to the insect but by then it will be too late for the insect. Eventually both types of products will work as long as the right amount of product is being used. Talstar P is a great choice to someone beginning to do their own pest control. Please see our Pest Library for more detailed information about specific pests.
Talstar P is a excellent option for boxelder bugs. Be sure to spray around the perimeter of the home, around windows, doors, etc. where the bugs could get indoors. You should treat in late Summer and Fall once a month until the first frost. This product can also be used indoors around the perimeter of your home. The mixing ratio is 1 fl. oz. per gallon of water.
Be sure that you do not expect rain for at least 2 hours after Talstar P (Talstar One) application. Once dried Talstar leaves a residual for 2-3 months.
Talstar P(Talstar One) will kill deer flies that come in direct contact with the treated surfaces.
